Unwind and feed
Review roll width, diameter, weight and material behaviour to choose the feed setup.
HYD-S SERIES · FLOOR-STANDING ROLL CUTTING
See this machine’s application
Compare nine HYD-S floor-standing roll cutting models with maximum blade widths from 500 to 1600 mm. For cut-to-length cross-cutting of fabrics and nonwovens; confirm slitting tooling by model and material.
Models are ordered by maximum blade width. Select a model to include it in your enquiry.
500 mm
60 m/min · 170 kg
Enquire about this model ↗600 mm
60 m/min · 185 kg
Enquire about this model ↗700 mm
60 m/min · 200 kg
Enquire about this model ↗800 mm
60 m/min · 220 kg
Enquire about this model ↗1000 mm
60 m/min · 338 kg
Enquire about this model ↗1200 mm
60 m/min · 350 kg
Enquire about this model ↗1300 mm
80 m/min · 600 kg
Enquire about this model ↗1500 mm
60 m/min · 700 kg
Enquire about this model ↗1600 mm
80 m/min · 780 kg
Enquire about this model ↗Cutting speeds are reference values from the model sheets. Confirm usable width, cut length, tolerance and output for your material and configuration. Power can be configured for your site.
| Model | Blade width (mm) | Cutting speed (m/min) | Cut length (mm) | Weight (kg) | Dimensions L × W × H (mm) | Blade motor (W) |
|---|---|---|---|---|---|---|
| HYD-500S | 0.1–500 | 60 | 0.5–99999.9 | 170 | 1480 × 830 × 1200 | 250 |
| HYD-600S | 0.1–600 | 60 | 0.5–99999.9 | 185 | 1480 × 930 × 1200 | 250 |
| HYD-700S | 0.1–700 | 60 | 0.5–99999.9 | 200 | 1480 × 1030 × 1200 | 250 |
| HYD-800S | 0.1–800 | 60 | 0.5–99999.9 | 220 | 1480 × 1130 × 1200 | 400 |
| HYD-1000S | 0.1–1000 | 60 | 0.5–99999.9 | 338 | 1530 × 1300 × 1200 | 600 |
| HYD-1200S | 0.1–1200 | 60 | 0.5–99999.9 | 350 | 1530 × 1530 × 1200 | 600 |
| HYD-1300S | 0.1–1300 | 80 | 0.1–99999.9 | 600 | 2000 × 1600 × 1300 | 750 |
| HYD-1500S | 0.1–1500 | 60 | 0.1–99999.9 | 700 | 2100 × 2000 × 1300 | 750 |
| HYD-1600S | 0.1–1600 | 80 | 0.1–99999.9 | 780 | 2100 × 2100 × 1300 | 750 |
All nine sheets list SKD-11 tooling, a stainless steel panel and polyurethane rollers. Controller speed settings are separate from the cutting-speed figures above.
| Item | HYD-500S–1200S | HYD-1300S / 1500S / 1600S |
|---|---|---|
| Controls | 80 × 50 LCD | 7-inch touchscreen |
| Main feed motor | 500S / 600S: 86 × 118 closed-loop stepper; 700S–1200S: 86 × 156 closed-loop stepper. | 2000 W servo motor |
| Blade motor type | 500S–800S: AC geared motor; 1000S / 1200S: brake motor. | 750 W brake motor |
| Rear feed motor | 250 W variable-speed motor | 400 W variable-speed motor |
| Base frame | 500S–800S: 40 × 40 mm aluminium profiles; 1000S / 1200S: 40 × 80 mm profiles. Base height: 700 mm. | Integrated square-tube steel frame with casters and levelling feet. |
| Unwinding and receiving | Aluminium-profile roll stand and 650 mm receiving table. | Mechanically damped unwind stand, pneumatic tension arm and 650 mm receiving table. |
| Controller functions | Start/stop, blade delay and interval, batch pause and length compensation. Speed setting: 0–150. | Emergency stop; speed setting: 0–200 mm/s. |
| Total count setting | 1–999999 | 1–999999 |
| Included accessories | Power cord, No. 3/4/5/6 wrenches, spare fuse and manual. | Power cord, No. 3/4/5/6 wrenches and manual. |
Review roll width, diameter, weight and material behaviour to choose the feed setup.
Specify the number and width of strips and any edge trim before choosing the slitting tooling.
Use the actual material to assess the configuration and output for your cut length, tolerance and edge finish.
Fabrics and nonwoven rolls are the main applications shown here. Suitability for the listed materials depends on thickness, incoming form, tooling and trial results.









| Category | Examples |
|---|---|
| Foams, sponges and insulation | EVA foam, EPE foam and similar materials |
| Fabrics and textile trims | Fabric, nonwovens, webbing, zippers, hook-and-loop tape and cords |
| Plastics, films and adhesive materials | PET film, PVC film, graphene film, bubble film, battery film and double-sided adhesive stock |
| Tubing and sleeves | Heat-shrink sleeves, PVC and silicone tubing; check cross-section and how the material is held |
| Paper, card and packaging | Paper, card and packaging materials |
| Electronic, optoelectronic and insulating materials | Insulating paper, electrical-grade fibre paper, mica sheets and similar materials |
| Leather | Leather and synthetic leather |
| Sealing materials | Rubber, silicone and rubber seals |
| Thin metal stock | Copper and nickel strip, nickel sheet, aluminium foil and strip; confirm tooling and trial conditions |
| Composites and specialty materials | Share the layer structure, thickness and a sample |
Applications include packaging, electronics, appliances, battery and insulation materials, wire harnesses and automotive components.
A roughly 20-second reference video of slitting and cross-cutting on a similar machine, with English narration.
These photos show a reference machine arrangement.
These component photos are illustrative. Confirm the layout for the selected model and order.
Share the maximum incoming width, finished strip widths and trim allowance. Use the blade-width table for initial comparison, then confirm usable width with the tooling and material.
The sheets list slitting blades as optional on the 500S–1200S. The 1300S, 1500S and 1600S are combined slitting and cross-cutting machines. Confirm blade count, type and strip widths with the order.
These are reference cutting speeds from the model sheets. Finished output depends on the material, cut length, feed stability and tooling. Confirm it in a sample trial.
The model sheets list configurable power. Include your site voltage, frequency and phase with your enquiry.
MACHINE SELECTION & ENQUIRY
Share your material and finished-part requirements. HESPER can help you choose the HYD-S width, feed setup and tooling.
Start with what you have. Details you are unsure of can be confirmed later.
CONFIGURATION REVIEW
Share your project details so we can review the incoming material, finished dimensions and trial-cut requirements.