TAPE CUTTERS · ZIPPER TAPE

Continuous zipper chain arrives on a roll and leaves as hundreds of zippers of the same length. Cutting it by hand is slow, and the ends fray or come out crooked. Here is how to set up a tape cutter for zipper tape, and what to check first.

Guide · 6 min read

3 typesCoil, molded plastic and metal teeth: tell the supplier which one you cut
Teeth centeredGuide the chain so the cut runs square across the teeth
Hot or coldA hot knife can seal suitable polyester tape and nylon coil ends
Slider checkMake sure a slider still fits on the cut end before the batch

A bag workshop buys nylon coil zipper by the roll. Every order needs zippers in two or three lengths, so someone measures, marks and cuts the chain with scissors. The lengths drift a little, the tape ends fray before the slider goes on, and some cuts land at an angle across the teeth.

The same job comes up wherever continuous zipper is turned into finished zippers: bags, pouches, garments, cushions and tents. A tape cutter takes over the measuring and cutting. Zipper chain is not flat tape, though, so the setup and the cutting position need some thought.

THE SHORT ANSWER

Feed the zipper chain flat, teeth up, with the guides set to its full width so the teeth stay centered under the blade. Nylon coil chain is the usual job for a tape cutter. With molded plastic or metal teeth, tell the supplier the tooth material and where the cut has to fall before you choose a machine. On suitable polyester tape and nylon coil, a hot knife can seal the cut end; check that a slider still fits on it. Agree how zipper length is measured, then set length and quantity and check the first pieces.

  1. 01 Know your zipper chain
  2. 02 Feed it flat and centered
  3. 03 Hot or cold cut
  4. 04 Where the cut falls
  5. 05 Lengths and the slider
  6. 06 Check through the batch
  7. → HESPER machines
  8. ? FAQ

01 · KNOW YOUR ZIPPER CHAIN

Coil, molded plastic or metal

Continuous zipper, also sold as zipper chain or zipper by the yard, is two zipper tapes joined by a row of teeth. The teeth decide most of the cutting setup.

Zipper typeWhat the teeth areWhat it means for cutting
Nylon coilA continuous plastic coil sewn or woven onto the tapeThe usual job for a tape cutter. Test hot and cold cuts.
Molded plasticSeparate plastic teeth molded onto the tapeTell the supplier the tooth material and where the cut must fall.
MetalSeparate metal teeth clamped onto the tapeTell the supplier the tooth material and cutting position, and send a sample.
Three closed zipper chains side by side: metal teeth, molded plastic teeth and coil
Left to right: metal teeth, molded plastic teeth and coil. The teeth decide most of the cutting setup. Photo: Rabensteiner / Wikimedia Commons, public domain.
Related machines: Hot and Cold Tape Cutter · Cutting and Punching Machine

Coil sizes such as #3, #5 and #10 describe the size of the chain. Whatever the size, most zipper chain is much narrower than the 95 mm cutting width of HESPER's two narrow machines.

02 · FEED IT FLAT AND CENTERED

Keep the teeth under the blade

Zipper chain is thicker in the middle than at the edges. If it wanders in the guides, the cut runs at an angle across the teeth.

  • Set the guides to the full width. Both tapes and the teeth should pass straight through, with the teeth centered.
  • Same side up. Feed the teeth facing the same way on every piece, so the zippers are consistent at sewing.
  • Let it come off the roll freely. A clear, straight path from the roll stops the chain from twisting.
  • Check the feed roller grip. It should move the chain without slipping over the teeth. If the cut drifts, read why tape feeds crooked.
A closed coil zipper lying flat on paper, teeth centered between the two tapes
Coil zipper chain lying flat, teeth up and centered between the two tapes: the way it should pass through the guides. Photo: Oto Zapletal / Wikimedia Commons, CC0.
Related machines: Hot and Cold Tape Cutter · Cutting and Punching Machine

03 · HOT OR COLD CUT

Seal the end, but keep it usable

  • Hot cut. On suitable polyester tape and nylon coil, the heated blade can seal the cut end so the tape doesn't fray before sewing.
  • Watch the temperature. Too hot and the end can form a hard bead. Start low and raise it in small steps.
  • Check the slider. If a slider goes on from the cut end, make sure it still fits after hot cutting.
  • Cold cut. Use it when the end will be covered or finished later, or when the tape is not a heat-sealable fiber. See hot knife or cold knife.

04 · WHERE THE CUT FALLS

Agree the cutting position first

With coil chain, the cut usually goes straight through the tape and the coil. With separate teeth, where the cut lands matters more: through a tooth, between teeth, or in a gap where the teeth have been removed.

  • Tell the supplier. Zipper type, tooth material, chain size and where the cut has to fall.
  • Send a sample. A short length of your chain is the quickest way to check the blade and feed setup.
  • Don't assume. A setup that cuts coil chain well is not proof that it will cut molded or metal teeth the way you need.

05 · LENGTHS AND THE SLIDER

Agree how a zipper is measured

Zipper length can be measured from tape end to tape end, or along the teeth between the stops. Pick one and use it for both the setting and the check.

  • Allow for what comes next. Sliders, top stops and bottom stops are added after cutting. Leave the tape length those steps need.
  • One length per batch. Run each size as its own batch and bundle it before changing the setting.
  • Set length and quantity once. The machine feeds, cuts and counts, so nobody measures or counts by hand.

06 · CHECK THROUGH THE BATCH

First pieces, then now and then

  • Measure the first pieces. Lay them flat and compare with the setting.
  • Look at the cut. Square across the teeth, ends sealed or clean, no crushed teeth.
  • Fit a slider. Try one on a cut piece before running the full batch.
  • Recheck as the roll shrinks. Measure a piece now and then during the run.

HESPER EQUIPMENT

HESPER hot and cold tape cutting machines

Four options, each listed with hot and cold knife cutting. Zipper tape is one of the materials listed on the tape cutter page, which also has a short video of zipper tape cutting.

95 MM

95mm EconomyCutting width 1–95 mm. Button control panel for routine cut-to-length work.

95 MM

95mm High-SpeedCutting width 1–95 mm. LCD and buttons.

210 MM

210mm TouchscreenCutting width 1–210 mm for wider tapes and webbing.

310 MM

310mm TouchscreenCutting width 1–310 mm for the widest strips.

? FAQ

Zipper tape cutting questions

Can a tape cutter cut zipper tape?

Yes. Zipper tape cut-to-length is listed for HESPER tape cutters. Tell HESPER the zipper type, tooth material and where the cut has to fall.

Which zipper chain is easiest to cut?

Nylon coil chain is the usual job. Molded plastic and metal teeth need the cutting position agreed first.

Should zipper tape be hot cut?

On suitable polyester tape and nylon coil, a hot knife can seal the end. Test the temperature and check that a slider still fits.

Why are my cuts crooked across the teeth?

The chain is moving in the guides. Set the guides to the full width so the teeth stay centered.

How should zipper length be measured?

Tape end to tape end, or along the teeth between the stops. Agree one way and use it every time.

Does the machine fit sliders or stops?

No. It cuts the chain to length. Sliders and stops are added afterward.

What should I send for a quote?

Zipper type and size, tooth material, the lengths and quantities you cut, and a short sample.

ZIPPER TAPE

Still Cutting Zipper Chain by Hand?

Send HESPER the zipper type and size, the tooth material, where the cut has to fall, and the lengths and quantities you cut. A short sample of your chain is the quickest way to find the right setup.

Send your zipper details · See the tape cutters · sales@hespermachine.com

← Back to the blog