BAG MAKING · CPE FLAT BAGS

Heat sealing bags one by one and cutting them with scissors works for a few dozen. At a few thousand, the seals vary, the lengths drift and someone spends the day counting. Here is how a heat sealing and cutting machine turns a film roll into flat bags, and what to check before you buy one.

Guide · 6 min read

Seal + cutFeed, heat seal and cut to length in one pass
310 mmMaximum cutting width of the CXY-300GD flat bag machine
1–60Cuts per minute listed for the CXY-300GD; not the same as finished bags
Air neededThe sealing assembly is pneumatic: plan for compressed air

A small packaging workshop makes plain CPE bags for a customer. One person runs a hand sealer, another cuts the film to length, and a third counts and bundles. Some seals are weak at one end, some bags are a few millimeters longer than others, and every batch is counted twice.

The same job comes up wherever flat bags are made from a film roll in small and medium runs. A heat sealing and cutting machine feeds the film, seals across it and cuts each bag to the set length, then counts the batch. What it cannot do is guess your film or your seal requirements, so those need to be checked with your own material first.

THE SHORT ANSWER

A flat bag machine feeds film from the roll, heat seals across it and cuts each bag to a set length. If the roll is a flat tube of film, each seal and cut gives a bag that is sealed on one end and open on the other. Before you buy, check four things with your own film: that the seal holds, that the seal sits where you want it relative to the cut, that the bag length stays steady through the roll, and how many finished bags per minute you actually get. Send a sample bag or drawing, your film details and your target output for a quote.

  1. 01 What the machine does
  2. 02 Know your film
  3. 03 Getting a good seal
  4. 04 Bag length and counting
  5. 05 Cuts per minute vs bags per minute
  6. 06 Shaped ends and holes
  7. → HESPER machines
  8. ? FAQ

01 · WHAT THE MACHINE DOES

Feed, seal, cut, count

A heat sealing and cutting machine for flat bags works in a simple cycle:

  • Feed. Rollers pull the film from the roll to the set length.
  • Seal. A heated sealing bar presses across the film and joins the layers.
  • Cut. A blade cuts the film so the finished bag drops off.
  • Count. The controller counts each bag and stops or pauses at the batch quantity.

With a flat tube of film, each seal closes one end of a bag and the cut opens the next. The result is a flat bag sealed on one end and open on the other, ready to fill.

Diagram: a flat tube of film feeds from the roll, is sealed and cut, and becomes a flat bag sealed on one end
How a flat bag is made from a flat tube of film: seal across, cut, repeat. Illustration by HESPER. View the CXY-300GD flat bag machine

02 · KNOW YOUR FILM

Tell the supplier what is on the roll

The film decides most of the setup. Before you ask for a quote, write down:

  • Film construction. CPE, PE or another film; a flat tube or a single layer; plain, printed or embossed.
  • Thickness. Thickness changes how the film seals and how it feeds.
  • Roll size. Roll width, outside diameter and weight. See how to specify an unwind roll.
  • The finished bag. Bag width, bag length, where the seal goes and what the seal has to do.
Diagram of film cross-sections: flat tube, single layer and folded film
Flat tube, single layer or folded film: tell the supplier which one is on your roll. Illustration by HESPER. View the CXY-300GD flat bag machine

03 · GETTING A GOOD SEAL

Test the seal on your own film

The seal is the part that makes it a bag. Thickness range and sealing conditions depend on the material, so test with a sample before you agree the setup.

What you seeLikely causeWhat to change
Seal peels open easilySealing conditions not matched to the filmRe-test the seal setting with your film and thickness
Seal is thin, shiny or burned throughToo much heat or pressure for the filmLower the seal setting and test again
Wrinkles across the sealFilm not lying flat into the seal barCheck the guides and feed-roller pressure
Seal too close to, or through, the cutSeal and cut position not agreedSet the seal position against your bag drawing
Bag lengths driftFilm slipping or roll tension changingCheck roller pressure and the roll holder
  • Pull test. Pull each side of a sealed bag apart by hand. The seal should not open before the film around it gives way.
  • Fill test. Fill a few bags with the real product and handle them the way your customer will.
  • Check through the roll. Seal quality should stay the same as the roll gets smaller.
Diagram of a flat bag drawing marked with bag width, bag length, seal position, seal-to-edge distance and open end
What to mark on the bag drawing you send for a quote. Illustration by HESPER. View the CXY-300GD flat bag machine

04 · BAG LENGTH AND COUNTING

Set it once, check it often

On the CXY-300GD, the LCD and keypad have automatic and manual modes. You set length, speed, total quantity, batch quantity and pause delay.

  • Measure the first bags. Lay them flat and compare with the setting.
  • Use batch quantity. The machine pauses at each batch so bundles are already counted.
  • Use the pause delay. It gives the operator time to take each bundle away.
  • Feed the film flat. Movable guide bars and guide wheels, with adjustable feed-roller pressure, keep the film straight. See will a cutting machine stretch thin material.

05 · CUTS PER MINUTE VS BAGS PER MINUTE

Read the speed figures carefully

The CXY-300GD lists a cutting rate of 1–60 cuts per minute and a feed speed of 700 mm/s. These are machine specifications, not finished-bag output.

  • Longer bags take longer. The film has to feed the full bag length before every seal and cut.
  • Sealing takes time. The seal bar has to stay closed long enough to make a good seal on your film.
  • Ask for a trial. Real output depends on film, bag length and sealing conditions. A trial with your film gives the number to plan with.

06 · SHAPED ENDS AND HOLES

Beyond a straight cut

The CXY-300GD page shows blade and tooling options from a straight cut to angled, V-notched, pointed, rounded and serrated ends, and cutting with punching. Shaped cuts and punching should be confirmed with a sample of your film.

HESPER EQUIPMENT

HESPER film sealing and cutting machines

Specifications are as listed on each product page. Confirm thickness, minimum dimensions and real output with your own film.

FLAT BAGS

CXY-300GD CPE Flat Bag Heat Sealing and Cutting MachineMaximum cutting width 310 mm. 1–60 cuts/min, feed speed 700 mm/s. 220 V / 50 Hz, 900 W, electric + pneumatic. Chinese / English LCD and keypad. View the machine

WIDER FILM

HYD-600 PVC and PE Film Heat Sealing and Cutting MachineCut width 0.1–600 mm, cut length 0.1–9999.9 mm. 220 V / 50 Hz. Heat-sealing configuration is confirmed separately for each film. View the machine

? FAQ

Flat bag sealing and cutting questions

What does a heat sealing and cutting machine do?

It feeds film from the roll, seals across it with a heated bar and cuts each piece to the set length, then counts the batch.

Can it make bags from a film roll?

Yes. The CXY-300GD is listed for CPE flat bags. With a flat tube of film, each seal and cut gives a bag sealed on one end.

What film thickness can it seal?

The thickness range depends on the material and is not listed as a single figure. Test with your film.

How many bags per minute will I get?

The 1–60 cuts per minute figure is a machine specification. Real output depends on film, bag length and sealing conditions.

Does it need compressed air?

Yes. The CXY-300GD is electric + pneumatic, so tell the supplier about your site power and air supply.

What should I send for a quote?

Film construction and thickness, roll width, diameter and weight, a sample bag or drawing with the seal position, your target output and batch size.

FLAT BAGS

Still Sealing and Cutting Bags by Hand?

Send HESPER your film type and thickness, roll size, a sample bag or drawing with the seal position, and how many bags you need per day. A short length of your film is the quickest way to check the seal.

Send your bag details · See the flat bag machine · sales@hespermachine.com

← Back to the blog