
▶You buy thin aluminum sheet, but your product needs aluminum strips: trims, spacers, battery and electrical parts or packaging inserts. Cutting them with tin snips or a hand shear works for a few pieces. As demand grows to hundreds of strips a day, repeated measuring, marking and hand cutting can slow production, with inconsistent widths, uneven edges or bent narrow strips becoming concerns.
A shearing machine addresses the repeated cutting task by cutting across the whole sheet width in one stroke, strip after strip. This guide uses a short HESPER demo, with aluminum sheet stated as 605 mm wide and 0.6 mm thick, to show how it works and what to prepare so you get the right aluminum cutting machine for your strips.
How to cut aluminum sheet into strips with a shearing machine
In the demo, the blade crosses the full 605 mm width in a single stroke for each cut, and each stroke produces one long, narrow strip. The strips are collected in a bundle and the cut edges are shown close up. The machine in the demo is HESPER’s tabletop automatic roll to sheet cutting machine. The process discussed here is cross-cutting into strips.

Compared with hand cutting, the difference is simple: one straight cut across the sheet instead of many small snips along it.
Problem 1: strip widths drift. Set the width, then check it.
When you cut by hand, every strip is measured and marked again, so small errors add up. When the aluminum is fed from a coil on HESPER’s tabletop automatic roll to sheet cutting machine, the strip width is the cut length you set on the control panel. Stepper feeding advances the material by the set step, reducing repeated measuring and marking. In this cross-cutting arrangement, the feed step sets the strip width, while the incoming material width becomes the strip length (stated as 605 mm in the demo). This differs from longitudinal slitting along a coil.
Check the first piece, including strip width at both ends, before batch cutting. Sample strips from the start, middle and end of the run. Use length compensation for a consistent offset; if dimensions vary randomly, investigate feeding, slip or material skew first. Compensation does not remove random variation.
Problem 2: wavy edges and burrs
Full-width shearing reduces the need for successive snip cuts, but one stroke does not guarantee a burr-free or perfectly flat strip. Edge quality also depends on alloy, temper, blade condition and clearance. Define acceptable burr, edge straightness and subsequent bending requirements for the trial, then inspect the samples. Use appropriate gauges for quantified requirements rather than judging from photographs alone.

Problem 3: narrow strips curl, or coated sheet gets scratched
Very narrow strips cut from thin aluminum sheet can curl or twist. Painted, anodized or film-covered sheet needs a clean cut without peeling or scratching the surface. Send the strip width and coating or protective-film details. Check trial strips for flatness, scratches and lifted film, and assess guiding, support and collection so strips are not bent or scratched after leaving the blade.

Which HESPER aluminum sheet cutter fits your job
If you are comparing a sheet metal shearing machine with other cutting options, start from your strip size, your material and your daily quantity.
- Strips from aluminum coil: the Tabletop Automatic Roll to Sheet Cutting Machine lists aluminum strip and aluminum foil among its thin metal applications. For compatible rolls, it cross-cuts at a set feed step to produce strips; confirm the actual aluminum and feeding configuration with a sample.
- Choosing the width: it comes in 12 separate cutting-width configurations: 300, 400, 500, 600, 700, 800, 1000, 1200, 1300, 1500, 1600 and 1800 mm. For a 605 mm sheet, choose the 700 mm cutting-width configuration; 600 mm is too narrow. Confirm effective feed and cutting width and trial the actual sheet before ordering.
- Individual sheets instead of coil: tell us, because feeding, support and collection for single sheets are set up differently from roll feeding.
- Narrow metal strips: read how to specify thin metal and wire mesh cutting and choosing between CXY-100G, 100H and 100W.
For metal, send the grade and thickness: the 10 mm figure on the product page is a standard-blade figure for compatible materials, not a metal-cutting capacity. Need a shaped strip end? Blades can be customized by material and cut shape; assess the proposal with the complete machine configuration and provide a drawing or sample.
Before you request a quote: measure and send
- Aluminum alloy and temper (usually on the mill certificate or the supplier’s label)
- Thickness, measured at several points across the width, and whether a coating or film is included
- Sheet or coil width, and how the material is supplied
- Strip width, strip length and tolerance
- Acceptable burr and edge condition
- Quantity per hour or per day
- Photos or a sample of the material
- Your power supply (voltage and frequency)
FAQ
Can 0.6 mm aluminum sheet be sheared into strips?
Yes. In the HESPER demo, aluminum sheet stated as 0.6 mm thick and 605 mm wide was sheared across its full width into strips. For your own sheet, send the alloy, temper and strip size, and confirm it with a sample.
How do I keep aluminum strips the same width?
For cross-cut strips, the feed step determines strip width. Set it and check the first piece, then sample the start, middle and end of the batch. Length compensation can correct a consistent offset; random slip or material skew requires feeding checks first.
Will the cut edges have burrs?
Burrs are possible. A full-width stroke does not guarantee a burr-free edge; burr level depends on the material and tooling setup. Specify an acceptable burr requirement and confirm it through a cutting trial and appropriate measurement.
What machine width do I need for a 605 mm sheet?
Choose the 700 mm cutting-width configuration; 600 mm is too narrow for a 605 mm sheet. Confirm effective feed and cutting width and trial the actual material before ordering.
Need aluminum cut into strips? Send HESPER your alloy, thickness, width and the strip size you need, and we will suggest a machine and discuss a cutting trial. Send an enquiry or email sales@hespermachine.com.
