
A common first enquiry names only a model, for example: "Please send a quote for the CXY-100H." That is a clear start. A model can be priced. But whether that model is the right one for your metal cannot be judged from the model number alone.
This guide explains, in plain words, what the three versions of the HESPER thin metal sheet cutting machine have in common, which published ratings differ, and what to send so the quote you receive matches your job.
Compare the CXY-100G, CXY-100H and CXY-100W
All three are versions of the same Thin Sheet Metal & Wire Mesh Cut-to-Length Machine. This automatic metal cutting machine feeds strip and cuts it to a preset length. Its feed rollers, guides and spool support distinguish this setup from a handheld sheet metal cutter. The product page lists:
| Specification | CXY-100G Upgraded | CXY-100H Reinforced | CXY-100W High-speed |
|---|---|---|---|
| Power | 500 W | 650 W | 850 W |
| Maximum cutting cycles (listed rating) | 110 cuts/min | 110 cuts/min | 500 cuts/min |
| Cutting width | 100 mm | 100 mm | 100 mm |
| Listed feeding accuracy | 0.1 mm | 0.1 mm | 0.1 mm |
| Listed cutting tolerance | 2‰ | 2‰ | 2‰ |
| Power supply | 220 V / 50 Hz | 220 V / 50 Hz | 220 V / 50 Hz |
| Weight / size | 32 kg; 410 × 285 × 270 mm | ||
Feeding accuracy of 0.1 mm and cutting tolerance of 2‰ are separate listed ratings. They must not be read as a blanket finished-part accuracy guarantee. Agree the tolerance reference, measurement method and trial conditions for your actual material and finished length.
The page lists thin metal sheets, copper sheets, aluminum sheets and steel wire mesh as materials. The CXY-100H configuration lists an SKD11 blade, a stepper cutting motor, polyurethane feed rollers with pressure adjustment at both ends, material guides and a spool support. These configuration details are identified for the H version; confirm the G and W component specifications separately.

What the published comparison shows: power and cutting cycles
In the current product-page comparison table, two numerical ratings differ between the versions:
- Power: 500 W, 650 W or 850 W.
- Maximum cutting cycles: 110 cuts/min on the G and H, 500 cuts/min on the W.
The product page says to choose a version "according to power and cutting-cycle requirements". It also says that maximum cutting cycles are listed ratings, and actual output depends on the material, cut length and feeding conditions.
For a cut to length machine, output reflects both feeding and cutting time. As a general planning consideration, longer pieces can require more feeding time, so the higher cycle rating alone does not establish daily output. During a trial, measure acceptable finished pieces over a stated time with your own material and cut length.
Does "Reinforced" mean the CXY-100H cuts thicker metal?
The names Upgraded, Reinforced and High-speed are not material-specific thickness ratings. For thin metal and wire mesh, the grade, hardness, thickness or wire diameter, feed width and required edge quality must be considered together. Do not infer a greater metal thickness capacity from the word Reinforced or from power alone.
So do not choose the H only because the name sounds stronger. Send your metal details, and let the version be confirmed against your thickness and hardness with a sample.

First check: is the CXY-100 series right for your job?
Before comparing versions, check these three points:
- Width. All three list a 100 mm cutting width. If your strip is wider, it is outside the listed specification. Tell us the width so another option can be discussed.
- Material. The listed materials are thin metal sheets, copper sheets, aluminum sheets and steel wire mesh. If you are looking for an aluminum sheet cutter, send the grade and thickness of your aluminum as well. Other metals, coated metals or laminates need their details reviewed.
- Cut shape. A straight cut is the starting point. The page shows other cut profiles, but blade or tooling selection depends on the material, thickness, dimensions and machine model, and shaped cuts are confirmed with a sample.
What to send with "Please quote the CXY-100H"
The product page lists what is needed to confirm suitability. Add these to your enquiry:
- Metal: grade, hardness and thickness. For copper or aluminum, the grade or temper if you know it.
- Wire mesh: if you need a wire mesh cutter, give the wire diameter and aperture.
- Feed width and how the material is supplied (spool, coil or flat pieces).
- Cut lengths: the shortest and the usual length, and the length tolerance you need.
- Edge requirement: how much burr is acceptable.
- Target output: pieces per hour or per day.
- Photos or a sample of the material.
Our guide to specifying cuts for thin metal, copper sheet and wire mesh explains each of these in more detail.
What a useful quote should tell you
When you compare quotations for a sheet metal cutting machine, check that each one states:
- The exact version (G, H or W) and why it was chosen for your material
- The blade and any tooling for your cut shape
- What is included, such as the spool support
- The power supply: the page lists 220 V / 50 Hz, so check it against your site
- How length tolerance is defined. The page notes that feeding accuracy and cutting tolerance are separate listed ratings, and that the tolerance reference and test conditions should be confirmed for your material and length
- Lead time, packing, shipping, installation support and warranty terms, which the product page asks buyers to confirm with the enquiry
If you can, ask for cut samples or a short video made with your own metal.
Frequently asked questions
What is the difference between the CXY-100G, CXY-100H and CXY-100W?
The product page lists the same 100 mm cutting width, listed feeding accuracy, listed cutting tolerance, power supply, weight and size for all three. In that comparison table, power (500 W, 650 W and 850 W) and maximum cutting cycles (110, 110 and 500 cuts/min) differ. This does not establish that all other components are identical.
Does the CXY-100H Reinforced version cut thicker metal?
The name Reinforced does not establish a greater metal thickness capacity. Confirm the metal grade, hardness, thickness or mesh wire diameter, feed width and edge requirements through a sample trial for the proposed version.
Can I get a quote with only the model number?
A model can be priced, but its suitability for your material cannot be confirmed from the model number alone. Send the metal grade, hardness, thickness, feed width, cut lengths, tolerance, burr requirements and target output, plus photos or a sample.
What if my metal strip is wider than 100 mm?
All three versions list a 100 mm cutting width, so a wider strip is outside the listed specification. Send your width and material details so a suitable option can be discussed.
Ready to request a quote? Send HESPER the version you are interested in, together with your metal grade, thickness, width, cut lengths and target output. These details help confirm a suitable version and discuss sample-trial arrangements. Send an enquiry or email sales@hespermachine.com.
