Your customer wants a different edge finish. Can you change the fabric cutting machine blade on your CXY-1500T and switch from zigzag to straight cutting—or from straight cutting to zigzag?

The answer depends on the direction of the change. The CXY-1500T supports changing from zigzag-edge cutting to straight-edge cutting. It does not support changing from straight-edge cutting to zigzag-edge cutting.

Before ordering tooling, identify your fabric cutter’s current configuration and the edge finish required for the next job. These two requests need different answers.

AI-enhanced reference of the supplied zigzag-edge material sample
AI-enhanced reference based on the supplied zigzag-edge sample photograph. Generated detail is not measurement evidence.

From Zigzag to Straight Edges: Supported

If your CXY-1500T is configured for zigzag-edge cutting, changing to straight-edge cutting is supported.

However, confirm the appropriate tooling and changeover procedure with HESPER before purchasing replacement parts. Support for this change does not mean that any straight fabric cutting blade with similar dimensions will fit, or that the conversion is simply a matter of adjusting a control-panel setting.

Send your machine identification, photographs of the current cutting assembly and a sample of the required finished edge. Ask HESPER to specify the parts and setup instructions applicable to your machine.

This helps turn a supported change into a clearly defined production plan.

AI-generated straight-edge material illustration based on the supplied reference
AI-generated straight-edge illustration for comparison; not an actual CXY-1500T cutting result.

From Straight to Zigzag Edges: Not Supported

If your CXY-1500T is configured for straight-edge cutting, changing it to zigzag-edge cutting is not supported.

Do not assume that the supported change works in both directions. A machine that can be changed from zigzag to straight cutting should not automatically be treated as a machine that can freely alternate between both finishes.

If a new order requires a zigzag cutting machine, ask HESPER to assess a suitable configuration for the required edge finish before buying a zigzag blade.

The important step is to confirm a workable cutting solution before committing your existing equipment to the job.

HESPER fabric slitting and cross-cutting equipment with roll stand, feed path and output table
HESPER fabric slitting and cross-cutting equipment. Series photograph; the pictured unit’s exact model is not identified.

Show Exactly Which Edges Need to Change

“Change the edge” can mean different things to different customers.

Mark the required edges on a drawing or sample photograph. Does the finished piece need straight cut ends, straight sides, or straight edges around the entire piece?

Provide the finished length, width and dimensional tolerances. For zigzag requirements, include a clear reference sample or drawing showing the desired pattern.

Also distinguish between changing the machine for future production and trimming pieces that have already been cut. These are separate requirements and should be assessed separately.

Confirm Fabric Cutting Machine Blade Requirements Before Ordering

For a supported zigzag-to-straight conversion, ask HESPER to confirm:

  • Which replacement parts are required for your machine.
  • Whether any components beyond the blade need changing or adjustment.
  • Who should carry out the work.
  • Which setup checks are required before production.
  • How the straight-edge result will be verified using your material.

Do not assume a changeover time or installation method before these details are confirmed. Plan the work around the procedure supplied for your equipment.

Check the Finished Result With Your Material

After the supported changeover, run a trial before starting the full order.

Inspect several consecutive pieces for finished dimensions, edge straightness, cut completeness and any unacceptable surface or edge damage.

Use the material intended for production and agree on acceptance criteria beforehand. A straight-looking edge alone does not establish that the finished part meets the customer’s complete requirements.

Keep an approved sample and record the settings used for the trial. This gives the production team a clear reference when the order begins.

Need Both Edge Finishes? Explain That Before Choosing Equipment

If your orders regularly alternate between zigzag and straight edges, tell HESPER before selecting a fabric cutting machine or planning a conversion.

Explain how often the finish changes, which materials you process and what output each job requires. Ask for a configuration recommendation that addresses both products, including whether separate setups are needed.

For the CXY-1500T, the supported direction is zigzag to straight—not straight to zigzag. Confirm your current configuration and required finished edge before ordering tooling, then verify the result with an actual material trial.

← Back to the blogPrepare your requirements ↗