Stacked rolls of natural-colored material with visible cores
Roll width, outside diameter and weight are useful starting information. Illustrative material photo. Photo: Kaja Reichardt / Unsplash.

“I need an automatic cutting machine for PVC film. Which one should I buy?” The same question comes up for EVA foam, insulation paper, heat shrink tubing and nickel strip. Start with three decisions: the working width, the feeding and collection arrangement, and whether the job needs slitting as well as cross cutting.

This guide uses brochure-listed HYD specifications as model references. Material thickness, hardness, surface condition and the required finish still need to be considered before selecting a configuration.

What a Cut to Length Machine Does

A cut to length machine feeds strip or roll material and cuts across it at a set length. In roll-to-sheet work, this cross cutting step turns continuous roll material into individual sheets. Slitting is a separate operation that divides the material along its length. When a cross cutting machine is configured to turn roll material into individual sheets, it may be described as a roll to sheet cutting machine. Compare the actual feeding and cutting functions, as well as the machine name.

For example, the HYD-100D brochure lists a cut-length range of 0.5–99,999.9 mm, a total-quantity setting of 1–999,999, batch pause, cutter delay, cutter interval and length compensation. A setting range is not a cutting-accuracy specification or a guarantee that every material will run at its minimum length.

Blade specifications vary by model. The HYD-100D brochure specifies SKD11 blade material; SKD11 is a cold-work tool steel. Select the blade and feeding setup for the actual material rather than assuming that every HYD model has the same blade.

Step 1: Measure the Material and Feeding Width

Measure the widest material you plan to process. For several strips fed side by side, include the strip widths, gaps and guide arrangement. Check the usable feed path as well as the listed cutter width.

Extended yellow tape measure
Measure the material before comparing machine widths. Photo: josh A. D. / Unsplash.
Benchtop modelUpper end of listed cutter-width range
HYD-100D100 mm
HYD-200 / HYD-300200 / 300 mm
HYD-400 / 500 / 600 / 700 / 800400 / 500 / 600 / 700 / 800 mm
HYD-1000 / 1200 / 1300 / 1500 / 1600 / 18001,000 / 1,200 / 1,300 / 1,500 / 1,600 / 1,800 mm

These are width references, not material-specific recommendations. For thin metal strip, the brochure identifies HYD-100S as a benchtop metal cutting machine, with an effective width of 110 mm, a 250 W AC geared cutter motor and a listed cut-length range of 0.2–9,999.9 mm. Send the metal grade, thickness, width and edge requirements for a sample trial before selecting it for a nickel-strip job.

Step 2: Compare Feeding, Collection and Space

Benchtop and vertical describe the machine arrangement. Roll width or weight alone does not decide which one to buy. Compare the complete line: roll support, feeding, material guidance, collection space and the output required at your actual cut length.

Brochure itemHYD-100D benchtop exampleHYD-500S vertical example
Listed cutting speed34 m/min60 m/min
Feeding configurationStepper feed motorClosed-loop stepper feed motor; 250 W speed-controlled rear feed motor
Included stand / collectionL-type material standAluminum-profile material stand; 650 mm receiving platform
Machine dimensions400 × 380 × 400 mm1,480 × 830 × 1,200 mm
Machine weight30 kg170 kg

The dimensions above are machine dimensions, not the full operating space. Allow for the roll, material travel, collection and operator access. Check roll outside diameter, core diameter and weight against the proposed unwinding setup.

The listed 34 and 60 m/min values are brochure ratings, not promised finished pieces per minute. Actual output depends on cut length, material behavior, the cut cycle, pauses and collection. Compare trial results under the same job conditions.

Step 3: Decide Whether You Also Need Slitting

If the incoming roll is wider than the required finished strips, specify both the slit widths and the cross-cut length. HYD-100D and HYD-500S brochure pages list longitudinal blades as an option for combined slitting and cross cutting. Include that option explicitly in the quotation.

For a wider integrated arrangement, the HYD-1300S and HYD-1600S brochure pages list a 7-inch touchscreen, a 2,000 W servo feed motor, a pneumatically adjusted tension arm and mechanical damping on the unwinding stand. Both list 80 m/min. These specifications apply to these two models; the appropriate configuration still depends on the material and finished strip requirements.

Beyond the Material Name: What Else to Check

The brochure lists foam, textiles, film, tubing, paper, insulation materials, leather, rubber and thin metal. Treat that list as application categories rather than proof that every grade and thickness works on every model.

Example jobInformation that helps select the configuration
EVA foam sheet or stripThickness, compressibility, width and acceptable edge condition
PVC or PET filmThickness, surface finish, roll dimensions and cut-length tolerance
Insulation paperThickness, width, finished length and edge requirements
Heat shrink tubingDiameter, wall thickness and acceptable end deformation
Nickel or copper stripGrade, thickness, width and acceptable burr level

For buyers searching for a foam cutting machine, this guide concerns feeding foam sheet or strip and cutting it to length. Block slicing and 3D contour cutting are separate process requirements and should be discussed separately. For several materials, assess each sample and the required blade or feed adjustments.

What to Send with an Enquiry

  1. Material name, grade and thickness
  2. Material width and number of strips fed together
  3. Finished length, tolerance and edge-quality requirements
  4. Roll outside diameter, core diameter and weight
  5. Required quantity per day and available production hours
  6. Slitting requirement, slit widths and number of lanes
  7. Local voltage, frequency and a material sample

Frequently Asked Questions

Is a benchtop automatic cutting machine enough for my workshop?

Compare the material width, roll support, feeding arrangement, collection space and required output at the actual cut length. HYD-100D is a compact benchtop example, but the material sample and full configuration determine suitability.

What foam-cutting work does this guide cover?

It covers feeding foam sheet or strip and cutting it to length. Block slicing and 3D contour cutting are separate process requirements. Provide the foam thickness and sample for evaluation.

What does the 0–80 speed setting mean?

The HYD-100D brochure identifies 0–80 as a control setting, not the cutting speed. Its listed cutting speed is 34 m/min. Control-setting ranges differ by model, and neither number is a finished-pieces-per-minute rating.

Can one cut to length machine handle several materials?

The brochure lists several application categories. Assess each material, thickness and finished-part requirement with a sample trial and select the corresponding blade and feeding setup.

Can the machine use my local power supply?

The brochure states that the power supply can be customized to customer requirements. Provide the voltage and frequency so that HESPER can specify the electrical configuration in the quotation.

Tell HESPER what you need to cut. Share the material and job details to compare the HYD configurations and arrange sample evaluation. Send an enquiry or email sales@hespermachine.com.

← Back to the blogPrepare your requirements ↗